G4A8R
Hover over image to zoom in

G4A8R

Availability: Obsolete
OBSOLETE Remote Analog 8-channel Multifunction I/O Unit Mistic Protocol

Production Specification

*** This part is obsolete and no longer available.***
Remote Analog 8-channel Multifunction I/O Unit Mistic Protocol

If you need to replace this part, you may want to migrate to the SNAP PAC System. For migration information, see the FactoryFloor to PAC Project Migration Technical Note. Then contact our Opto 22 Pre-Sales engineers with details about your specific application so they can help recommend parts.

This part is obsolete and no longer available.
CPU
CPU clock Frequency
16-bit, Intel 80C 196 processor 12 MHz processor
Communications
    Bus speed
    Cable type

    Maximum cable length
    Mode

300-115.2 KBd
2 twisted pair + GND
Interrupt uses 1 twisted pair
3,000 ft (more with repeaterss)
Binary or ASCII
Typical I/O time (includes communication transfer time)
    Read 16 channels
    Write 16 channel


5.53 ms
6.52 ms
Input/output update rate
   Input
   Output

7 ms
50 ms
Analog input/output timing Analog Mistic 200 I/O units constantly update the status of their I/O. Input modules are read every 7 milliseconds and the data held in memory until requested by their host CPU. Output module data is held in memory and output to each module every 50 milliseconds.
PID scan rate 100 ms for all 8 PID•s
4 PID loops/brick
Up to 8 PID loops with brick expansion
option
Typical Event/Reaction time (<16 Event/Reactions) 4 ms
*System power consumption @ 24 VDC ± 0.1 V
   (excludes analog modules)
   Terminated (last brick on the bus)
   Non-terminated (all other bricks)
   Analog expansion brick
   Typical analog module



180 mA
180 mA
 65 mA
 45 mA
Isolation
   Input to output
   Output to analog supply

4,000 Vrms
4,000 Vrms
Temperature
   Operating
   Storage

0° C to 70° C
-40° C to 80° C
Humidity 5% to 95% relative humidity
Software OptoControl, Cyrano 200, and Misticware
Expansion options
G4RAX Remote analog expansion brick
Adds 8 additional analog I/O channels on a separate brick unit
Agency Approvals UL, CE, DFARS; UKCA

Mistic Analog I/O Brick Data Sheet

**** This product is obsolete and no longer available.****

The G4A8R is a high performance analog I/O brick for the Opto 22 family of processors and I/O.

Mistic Installation Guide

Guide for configuring and installing the Mistic 200 System.

UKCA Declaration of Conformity (ATEX, EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with the rules, regulations and standards of the United Kingdom. The models cited have been tested to the essential requirements listed in the Standards section, and fully comply with the legislation as listed in UK Legislation section.

SNAP PAC System Migration Technical Note

This document describes migration options for customers integrating the SNAP PAC System with older Opto 22 systems. It explains the SNAP PAC System's similarities and differences with earlier systems, defines legacy products, and shows how to mix old and new hardware.

Customers moving to the SNAP PAC System may also want to consult form #1693, Legacy and Current Product Comparison and Compatibility Charts.

UL Approval Document

This document lists all Opto 22 part numbers that have the Underwriters Laboratory (UL) approval.

CE Declaration: Component

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

CE Declaration: Low Voltage

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

host60.zip

Mistic I/O is a serial (RS422/485) protocol allowing up to 4,096 I/O points (per serial link) to be connected to a computer or Mistic controller used with Mistic-protocol brains and brain boards such as the B100, B200, and B3000. For use with Mistic controllers and I/O.

Mistic I/O Scanning Utility

Mistic I/O is a serial (RS422/485) protocol allowing up to 4,096 I/O points (per serial link) to be connected to a computer or Mistic controller used with Mistic-protocol brains and brain boards such as the B100, B200, and B3000. For Microsoft Windows 95/Windows NT users.

No videos or demos are available for this product.