Products > SNAP-LCSX-PLUS
SNAP-LCSX-PLUS
Hover over image to zoom in

SNAP-LCSX-PLUS

Availability: Obsolete
OBSOLETE SNAP Controller with Four COM Ports for FactoryFloor systems
Data Sheet

Production Specification

*** The SNAP-LCSX-PLUS is obsolete and no longer available as of January 2014, due to the unavailability of essential parts.***

For new development we recommend using the SNAP-PAC-S2 standalone controller and the PAC Project Professional software suite instead of the SNAP-LCSX and FactoryFloor. SNAP PAC S-series controllers with PAC Project Pro offer a migration path for legacy mistic systems. The SNAP-PAC-S2 controller is slightly larger than the LCSX. It provides more power and offers more features, including 4 configurable serial ports plus Ethernet network connections.

To compare product features, see Legacy and Current Product Comparison and Compatibility Charts.

For more information on migration, see the FactoryFloor to PAC Project Migration Technical Note.

------------

The SNAP-LCSX-PLUS controller provides real-time industrial control in a small footprint. It is designed to work with the FactoryFloor software suite and with SNAP brains, racks, and analog and digital SNAP I/O modules. Top-mounted serial ports include a dedicated Opto 22 remote I/O port and three RS-232 or RS-485 serial port.

NOTE: The SNAP-LCSX-PLUS is NOT compatible with PAC Project software.
*** This product is obsolete and no longer available. ***

Item

Specification

CPU

32-bit Motorola 68EC020 processor

CPU clock frequency

16.67 MHz

Memory
    RAM
    Flash ROM

  

1 MB with battery backup
256 KB

RAM/clock battery

3.6-volt lithium, non-rechargeable, user replaceable, p/n G4BATT32

I/O

Opto 22 remote I/O using RS-485

Communication

COM 0: jumper selectable as RS-232 or RS-485, 2-wire or 4-wire. Modem control signals are present for RS-232 (RTS, CTS, DTR, DCD, and R). Pull-up, pull-down, and termination are jumper selectable for RS-485 operation, allowing multidrop operation.

COM 1: dedicated Opto 22 remote I/O port (2-wire RS-485 with interrupt capability)

COM 2 and COM 3 (LCSX-PLUS only): jumper selectable RS-232 or RS-485. RS-232 signals include TX, RX, RTS, and CTS. RS-485 is either 2-wire or 4-wire, with selectable termination and biasing.

Note: All ports use low-noise slew-rate-limited drivers and are transient protected to 400 W.

Real-time clock

Clock/calendar, Epson 64613 with battery backup

Power requirements

5 VDC ± 5% at 500 mA (maximum)

Typical operating temperature

0 °C to 70 °C

Storage temperature

-40 °C to 85 °C

Humidity

5% to 95% relative humidity, non-condensing

Software

FactoryFloor (OptoControl, OptoDisplay, OptoServer, and OptoConnect) and Classic software (Cyrano, Mistic MMI, and MDS)

System monitor

Processor and power watchdog timers
Agency Approvals DFARS, RoHS

1047

SNAP LCSX Controllers Data Sheet

*** These products are obsolete and no longer available. ***
The SNAP-LCSX and SNAP-LCSX-PLUS controllers are the cost-effective answer to applications requiring small, powerful, real-time industrial control.

View

1061

SNAP-LCSX and LCSX-Plus User's Guide

This manual contains information about configuration, installation, and communications connections to the SNAP-LCSX and SNAP-LCSX PLUS controller.

View

RM_OCTRL_FW

OptoControl-based Controller Firmware README

This README file lists revision changes made to the firmware used in the following Opto 22 controllers that run OptoControl strategies: G4LC32, G4LC32SX, M4, M4IO, M4RTU, SNAP-LCSX, SNAP-LCSX-PLUS, and SNAP-LCM4.

View

RM_CYR_FW

Cyrano-based Controller Firmware README

This README file lists revision changes made to the firmware used in the following Opto 22 controllers that run Cyrano strategies: G4LC32, G4LC32SX, G4LC32ISA, G4LC32ISA-LT, M4, M4IO, M4RTU, M4RTU Rev.2, SNAP-LCM4, SNAP-LCSX, and SNAP-LCSX-PLUS.

View

1739

Case Study: Michigan Fish Hatcheries

At fish hatcheries throughout the state of Michigan, Opto 22 SNAP PAC systems interface with flowmeters, float level sensors, variable frequency drives, and the other power-, oxygen-, and water-related equipment to automate, manage, and monitor equipment used during every stage of the fish rearing process. Also monitored and managed are a variety of water conditions such as tank water temperatures, water flow and oxygenation, as well as the on/off status of equipment.

Watch the Michigan Fish Hatcheries video case study.

View

1688

SNAP PAC System Migration Technical Note

This document describes migration options for customers integrating the SNAP PAC System with older Opto 22 systems. It explains the SNAP PAC System's similarities and differences with earlier systems, defines legacy products, and shows how to mix old and new hardware.

Customers moving to the SNAP PAC System may also want to consult form #1693, Legacy and Current Product Comparison and Compatibility Charts.

View

1309

Caso: Redes de Distribución de Agua en Monterrey, México (Spanish)

Caso sobre la automización de un amplio sistema acuífero en la ciudad de Monterrey, NL en México. (Case study describing a large water/wastewater control project in the city of Monterrey, Mexico. Document is in Spanish.)

View

0959

SNAP-PSDIN Installation Note

This document describes how to install a SNAP DIN-RAIL mounting assembly.

View

0891

CE Declaration: Low Voltage

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

View

BETA firmware for OptoControl-based controllers

This download contains BETA firmware for Opto 22 controllers running OptoControl strategies.

Beta Version Disclaimer:

OptoControl is a legacy product, which is no longer getting new features and no longer going through official release cycles. Beta versions of the firmware are made available as-is for those who need the related bug fixes.

In general, beta versions will include bug fixes since the last official release, without adding new features. This usually enhances product stability without introducing unwanted side effects. Beta versions for legacy products have been through basic testing only, and will not be formally tested.

Ultimately, the choice will be up to the user as to whether the benefit of using the beta version is worth the risk. We simply want to make the beta version available so that you have options.

View

SNAP-LCSX-PLUS Controller Firmware

This download contains the current firmware for the SNAP-LCSX-PLUS controller. The download also includes firmware for SNAP-LCM4, SNAP-LCSX, , M4, M4RTU, and other Opto 22 OptoControl-based controllers

View

AutoCAD Drawings

This file contains AutoCAD drawings of Opto 22 products dating from 1988 to 2003. These are the same drawings that have been available on our BBS. Included is an Excel file describing the file names and relevant Opto 22 part numbers.

View

Cyrano Flash Firmware

Current release of 16-bit Cyrano firmware. This firmware is required to run Cyrano strategies on legacy Opto 22 controllers.

View

Cyrano Flash Firmware and Installation Utility

Current release of 16-bit Cyrano firmware. This firmware is required to run Cyrano strategies on Opto 22 controllers. This file installs the Opto 22 Flash 200 utility (version R3.1i) and Cyrano firmware (version R3.2j).

View

Cyrano Software

The predecessor to OptoControl, Cyrano is a DOS application for flowchart control programming. This software does not run under Windows NT.

View

Mistic MDS

Mistic MDS is the predecessor to OptoServer. It is a DDE-only server for the Cyrano tagname database that operates under Windows 3.x.

View

Mistic MMI

Mistic MMI is the predecessor to OptoDisplay. It is a 16-bit Windows 3.x Man-Machine Interface package that is tightly integrated with Cyrano.

View

Modbus Library File for Modbus Integration Kit for OptoControl

Use this library file together with the Modbus Integration Kit for OptoControl.
 

View

OptoTerm Utility for OptoControl Controllers

This download contains a full installation of the most recent version of OptoTerm, a software utility for:

  • Downloading new firmware to an OptoControl-based controller.
  • Viewing the status of an OptoControl-based controller.

View
No videos or demos are available for this product.