Products > SNAP-UP1-ADS
SNAP-UP1-ADS
Hover over image to zoom in

SNAP-UP1-ADS

Availability: Obsolete
OBSOLETE SNAP Ultimate controller/brain, analog/digital/serial, for ioProject systems
Data Sheet

Production Specification

NOTE: This product is obsolete and no longer available. Contact Opto 22 pre-sales engineering for current options.

Although fully supported, this is a legacy product and not recommended for new designs. For new designs, the SNAP-PAC-R1-B on-the-rack controller has the same features as SNAP Ultimate but is more powerful. In addition, it works with the latest PAC Project automation software, with the most recent SNAP I/O modules, and with groov, the easy-to-use tool for building and viewing mobile operator interfaces. The SNAP-PAC-R1-B snaps into a B-series rack, so you don't need to change racks or wiring.

-------------

The SNAP Ultimate controller/brain is a programmable I/O and communications processor. It can be used as a rack-mounted controller or as an I/O unit in a larger control system based on a more powerful Opto 22 controller, such as the SNAP-PAC-S1.

Used as a rack-mounted controller, the SNAP-UP1-ADS is programmed using the legacy ioProject Basic software suite, which is included in the purchase price. The newer PAC Project software suite was designed for SNAP PAC controllers but also offers limited support for SNAP Ultimate I/O.

NOTE: Not all SNAP I/O modules are compatible with this controller. See Legacy and Current Product Comparison and Compatibility Charts to determine compatibility.

SNAP-UP1-ADS [Obsolete] , SNAP-UP1-D64, and SNAP-UP1-M64 [Obsolete]

Power Requirements

5.0 VDC to 5.2 VDC at 1.2 A maximum (does not include module power requirements)

Processor

32-bit ColdFire 5407

Memory:
  Total RAM
  Battery-backed RAM
  Flash EEPROM

  

16 MB
512 KB
8 MB

Backup battery

CR2032, fixed (not user replaceable)

Network Interface

IEEE 802.3 network, 10Base-T and 100Base-TX

Serial Port

RS-232

Serial Data Rates

Default is 19,200 baud; baud rate is soft-selectable from 150 to 115,200 baud.

Maximum Ethernet Segment Length

100 meters with Category 5 or superior UTP.
For 100 Mbps at this distance, use Category 5 or superior solid UTP.

Jumpers (Internal)

Boot to kernel/boot to loader
Reset to factory defaults

Temperature:
  Operating
  Storage

  

0 °C to 70 °C
-40 °C to 85 °C

Humidity

0–95% humidity, non-condensing

1473

ioProject Software Suite Data Sheet

*** NOTE:  Three products in this suite (IOPROJECTBAS, IOPROJECTPRO, and IOCONTROLPRO)  are OBSOLETE and no longer available.***

This data sheet describes Opto 22's legacy ioProject software suite, which provides control and HMI development tools for a SNAP Ethernet-based control system. The ioProject suite includes ioControl, ioDisplay, OptoOPCServer, and ioManager.

NOTE: For new development, use a SNAP PAC controller and PAC Project software.

View

1291

SNAP Ultimate Brain Data Sheet

*** NOTE: The SNAP-UP1-ADS and SNAP-UP1-M64 are obsolete and no longer available. The SNAP-UP1-D64 is available until limited stock is depleted. ***

For new development, see groov RIO and groov EPIC. ***

The SNAP Ultimate brain (SNAP-UP1-ADS, SNAP-UP1-D64, SNAP-UP1-M64) is an I/O and communications processor that mounts on a standard SNAP rack. The brain features 10/100 Mbps Fast Ethernet connectivity, programmability, and built-in enterprise connectivity. The brain is programmed using flowchart-based ioControl programming software, which is included in the purchase price of the SNAP Ultimate brain.

View

RM_UIO_FW

SNAP Ultimate I/O Firmware README

This README file lists revision changes made to the SNAP Ultimate I/O firmware used in SNAP Ultimate brains.

View

RM_IOPROJSS

ioProject Readme Notes

Readme for ioProject Basic and Professional, the legacy versions of PAC Project. Includes information on features, enhancements, and bug fixes for each ioProject application: ioControl, ioDisplay, OptoOPCServer, ioManager, and ioUtilities.

View

RM_ALL_ENET_FW

SNAP Legacy Firmware README

This README file lists revision changes made to the firmware used in SNAP PAC family controllers before Version 8.0a, the SNAP-LCE controller, and SNAP Ultimate, Ethernet, and Simple brains.

View

1714

Legacy Edition, PAC Manager User's Guide

This document is the Legacy Edition of the PAC Manager User's Guide. It includes information about both SNAP PAC hardware and older hardware.

Use this guide if you are using any legacy hardware (SNAP Ultimate, SNAP Ethernet, and SNAP Simple I/O, E1 and E2 brain boards) with PAC Manager (software part number PACMANAGER).

If you are using SNAP PAC controllers and SNAP PAC brains only, use Form 1704, PAC Manager User's Guide instead of this guide.

View

1678

Modbus/TCP Protocol Guide

This document shows you how to set up communication between Ethernet-based Modbus systems (using Modbus/TCP) and the groov EPIC system or SNAP PAC System.

In addition to groov I/O and the SNAP PAC System, the guide also covers Modbus/TCP communication with older Opto 22 Ethernet-based devices, including SNAP Ethernet, SNAP Simple, and SNAP Ultimate I/O; and E1 and E2 brain boards.

View

1555

Allen-Bradley DF1 Integration Kit For ioControl Users Guide

The Allen-Bradley DF1 Integration Kit (Part # IOP-INT-ABDF1) provides users of Opto 22’s ioControl software(version 6.0 and above) an easy method of communicating with Allen-Bradley drivers or PLCs using the DF1 protocol. Opto 22 controllers can act as either a “master” or a “slave” device. They can be connected directly to the serial port on an Allen-Bradley PLC or to Data Highway networks using standard Data Highway interface devices.

View

1465

OptoMMP Protocol Guide

This guide is for programmers who are writing custom applications to communicate with Opto 22 memory-mapped devices. These devices include groov EPIC processors; groov RIO modules; SNAP PAC controllers and SNAP PAC EB and SB brains; G4EB2 brains; SNAP Ultimate, SNAP Ethernet, and SNAP Simple I/O; E1 and E2 brain boards, and SNAP-LCE controllers.

The guide describes how to use the IEEE 1394-based OptoMMP memory-mapped protocol for programming. The guide also contains the complete memory map for all Opto 22 memory-mapped devices.

NOTE: This guide replaced previous individual programming guides for SNAP Ultimate I/O (form #1312) and SNAP Ethernet I/O (form #1227). This document was formerly called the "SNAP Ethernet-Based I/O Units Protocols and Programming Guide."

View

1460

SNAP Ethernet-Based I/O Units User's Guide

*** NOTE: These products are obsolete and no longer available. For new development, we recommend groov RIO and groov EPIC. ***

This guide shows you how to install, use, and troubleshoot I/O units that contain the following brains: SNAP-B3000-ENET, SNAP-ENET-S64, SNAP-UP1-M64, SNAP-UP1-ADS, SNAP-ENET-RTC, SNAP-ENET-D64, and SNAP-UP1-D64.

NOTE: This guide replaces previous individual user's guides for SNAP Ultimate I/O (form #1311) and SNAP Ethernet I/O (form #1112).

View

1440

ioManager User's Guide

ioManager is the software tool used to assign IP addresses and configure I/O points and system functions on most Opto 22 Ethernet-based hardware, including SNAP-LCE controllers: SNAP Ethernet, SNAP Ultimate, SNAP Simple, E1, and E2 I/O units; and SNAP-IT units. ioManager can also be used to directly read or write to these devices.

View

1314

ioControl Commands Quick Reference Card

Quick reference card for using ioControl, including all standard ioControl commands and their OptoScript equivalents. ioControl is part of the ioProject software suite.

View

1301

ioControl Command Reference

This command reference describes in detail all ioControl programming commands, or instructions. Use with form #1300, the ioControl User's Guide. ioControl is part of the ioProject software suite.

View

1300

ioControl User's Guide

The ioControl User's Guide includes programming instructions and tips for developing control strategies to run on SNAP Ultimate controller/brains and SNAP-LCE controllers. ioControl is part of the ioProject software suite.

View

1709

SNAP-RCK-B2M Rack Adapter Installation Note

This document shows you how to install the SNAP-RCK-B2M rack adapter. The adapter makes it possible to use a SNAP PAC rack or a SNAP M-series rack with a brain that would normally mount on a B-series rack (for example, the SNAP-UP1-ADS or the SNAP-B3000-ENET).

View

1688

SNAP PAC System Migration Technical Note

This document describes migration options for customers integrating the SNAP PAC System with older Opto 22 systems. It explains the SNAP PAC System's similarities and differences with earlier systems, defines legacy products, and shows how to mix old and new hardware.

Customers moving to the SNAP PAC System may also want to consult form #1693, Legacy and Current Product Comparison and Compatibility Charts.

View

1571

Caso: Soto la Marina (Spanish)

Caso sobre la automización de una planta de tratamiento de aguas en la ciudad de Soto la Marina, un puerto ubicado en la costa de Tamaulipas en el Golfo de México. (Case study of how a water treatment plant in Soto la Marina, Tamaulipas, Mexico, was automated.)

View

1059

FM Approval Document

This document lists all Opto 22 part numbers that have Factory Mutual (FM) approval.

View

SNAP-UP1-ADS Controller/Brain Firmware

This download contains current firmware for the SNAP-UP1-ADS controller/brain.

View

AutoCAD Drawings

This file contains AutoCAD drawings of Opto 22 products dating from 1988 to 2003. These are the same drawings that have been available on our BBS. Included is an Excel file describing the file names and relevant Opto 22 part numbers.

View

Allen-Bradley DF1 Integration Kit for ioControl

The Allen-Bradley DF1 Integration Kit provides users of Opto 22’s ioControl software (version 6.0 and above) an easy method of communicating with Allen-Bradley drivers or PLCs using the DF1 protocol. Opto 22 controllers can act as either a “master” or a “slave” device. They can be connected directly to the serial port on an Allen-Bradley PLC or to Data Highway networks using standard Data Highway interface devices.

View

Controller Time Synchronization Application

This software application updates the internal clock for an Ethernet-connected Opto 22 controller. The application runs in Windows at the command prompt, and can update controller clocks regularly or just once.

This application is used with the following Opto 22 controllers:

  • SNAP PAC S- and R-Series
  • Ultimate I/O (UIO)
  • SNAP-LCE
  • SNAP-LCM4
  • M4
  • M4RTU
  • M4IO
This download is freeware. Before downloading, read the Legal Agreement.

View

ioDoor Access Manager

ioDoor Access Manager is a sample utility program for use with SNAP-SCM-W2 serial communication modules. These modules comply with the Security industry Association Access Control Standard Protocol for the 26-bit Wiegand(R) Reader Interface.

The utility program, written in Visual Basic, manages user names and entry permissions. It is designed to be used with the sample ioControl strategy Door Control, which is a separate download.

This file is freeware. Before you download, read the Legal Agreements.

View

OptoAgent Integration (for CA Unicenter NSM 3.1)

OptoAgent Integration for CA Unicenter, in conjunction with Opto 22 SNMP-enabled Ethernet hardware, provides a convenient method for monitoring and managing real-world devices and business assets. OptoAgent allows for real-world data to be integrated into Unicenter.

 

The OptoAgent Integration supports both SNMP traps and polling to keep Unicenter updated on the current state of the hardware, and alert Unicenter of any problems. It also gives the user the ability to control the Opto 22 hardware.

OptoAgent Integration takes advantage of Unicenter Agent technology to graphically represent the Opto 22 hardware to the user. This Graphical User Interface (GUI) makes monitoring and managing real-world assets intuitive.

OptoAgent gives you the ability to read and write digital and analog I/O points that are attached to the Opto 22 hardware. These I/O points are connected to real-world electrical, mechanical, and electronic devices - such as lights, temperature and pressure sensors, motors, and serial devices. Using Unicenter, OptoAgent, and Opto 22 hardware, you can manage these real-world devices.

You can use ioManager software to configure the Opto 22 hardware and I/O points for use with OptoAgent. You can also configure OptoAgent to send SNMP traps based upon events you define.

Once the Opto 22 hardware and I/O points are configured, you can use OptoAgent View to see information about the Opto 22 hardware and the status and values of digital and analog I/O points.

View

Optomation Systems ioControl Functions

A piecewise linear interpolator function PLI under ioControl 5.1. The ioScript version can be easily copied to your program. It can be used for any of the following applications:

  • Calculating volume from tank level measurement (PV=Level Q=Volume)
  • Setpoint Generator (PV=Elapsed Time Q=Required Setpoint, eg Temp or Flow)
  • Flow rate profiling (PV=Dif Pressure Q=Flow Rate)
  • Split Range Control (PV=Common Output Q=Valve1 profile)
  • Adaptive Gain (PV=Secondary Variable Q=PID Gain Value)

View

Sample Door Control Strategy

The Door Control Strategy is a sample ioControl strategy for use with SNAP-SCM-W2 serial communication modules. These modules comply with the Security Industry Association Access Control Standard Protocol for the 26-bit Wiegand(R) Reader Interface. The sample strategy configures modules and handles access for up to 16 doors and up to 4200 users.

Also download ioDoorAccessManager, a utility program for managing user data.

This file contains sample code. Before you download, read the Legal Agreement.

View

SNAP Ethernet I/O BootP Server - Linux

A BootP server for configuring the IP address of the SNAP Ethernet brains and the M4SENET-100 adapter card.

Before you download, read the Legal Agreement.

View
No videos or demos are available for this product.

RELATED PRODUCTS