Snap-PAC R2 firmware Forum - Published: Hey All, My customer has 2 Snap-PAC-R2 controllers running and I need to enable RestAPI in both. One is running firmware version R9.4c and the other has version R8.4d. Before jumping off and updating...moreHey All, My customer has 2 Snap-PAC-R2 controllers running and I need to enable RestAPI in both. One is running firmware version R9.4c and the other has version R8.4d. Before jumping off and updating these I would like to ask if these two controllers can handle the latest firmware that allows Rest or might they be too old? Thanks Kevin... <less Snap-Pac-EB2 Firmware Question Forum - Published: I am replacing a Snap-Pac-EB2 with a replacement in kind, and I cannot get it to work with my application. The only difference I can see is my old module had an older firmware version. Is there a place...moreI am replacing a Snap-Pac-EB2 with a replacement in kind, and I cannot get it to work with my application. The only difference I can see is my old module had an older firmware version. Is there a place I can get older firmware files, and if so, would I be able to flash the unit with the older firmware? Thank you. The firmware version I am looking for is 200.3f... <less SNAP-PAC-R1 firmware upgradation failed Forum - Published: Hi all. I am using SNAP-PAC-R1 controller for my application. I tried to update the firmware of the module to R9.5h via Ethernet. During firmware downloading process suddenly an error called insufficient...moreHi all. I am using SNAP-PAC-R1 controller for my application. I tried to update the firmware of the module to R9.5h via Ethernet. During firmware downloading process suddenly an error called insufficient flash memory occurred. From then module is not responding. I tried to reset and restore. But no use. Please help me to resolve the issue and make my R1 to running state. Present situation is very worst. STAT LED blinks twice after power up and then it will goes OFF. No response from controller.... <less SNAP-PAC-EB1 Install Firmware via Ethernet Passthrough Connection Forum - Published: We configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With...moreWe configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With this configuration we alienate ourselves from inspecting the EB1 and installing firmware to the EB1 unless we are physically at the device. Not practicable for all of our remote locations. Building out a separate network is not an option. Is it possible to implement a procedure similar to the “I...... <less SNAP-PAC-R2 Firmware '...FTP Session Failed' Forum - Published: Am trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172...moreAm trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172.25.0.9 - Attempt to open FTP session failed”., note: the IP address is correct. I have tried using PAC Manager 9.0, 9.6 & 10.2; all produce the same error. Following the directions in the PAC Manager User Guide. I thought I had trouble with this years ago, but can’t locate any Opto help infor...... <less Firmware update Forum - Published: Hi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect...moreHi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect to it. I currently have this firmware R9.5h And also, if I update the firmware for the SNAP-PAC-R1, i have two other I/O hooked up to it, SNAP-PAC-EB1. do I also have to update the firmware for those too?... <less What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Snap-Pac-EB2 Firmware Question Forum - Published: I am replacing a Snap-Pac-EB2 with a replacement in kind, and I cannot get it to work with my application. The only difference I can see is my old module had an older firmware version. Is there a place...moreI am replacing a Snap-Pac-EB2 with a replacement in kind, and I cannot get it to work with my application. The only difference I can see is my old module had an older firmware version. Is there a place I can get older firmware files, and if so, would I be able to flash the unit with the older firmware? Thank you. The firmware version I am looking for is 200.3f... <less SNAP-PAC-R1 firmware upgradation failed Forum - Published: Hi all. I am using SNAP-PAC-R1 controller for my application. I tried to update the firmware of the module to R9.5h via Ethernet. During firmware downloading process suddenly an error called insufficient...moreHi all. I am using SNAP-PAC-R1 controller for my application. I tried to update the firmware of the module to R9.5h via Ethernet. During firmware downloading process suddenly an error called insufficient flash memory occurred. From then module is not responding. I tried to reset and restore. But no use. Please help me to resolve the issue and make my R1 to running state. Present situation is very worst. STAT LED blinks twice after power up and then it will goes OFF. No response from controller.... <less SNAP-PAC-EB1 Install Firmware via Ethernet Passthrough Connection Forum - Published: We configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With...moreWe configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With this configuration we alienate ourselves from inspecting the EB1 and installing firmware to the EB1 unless we are physically at the device. Not practicable for all of our remote locations. Building out a separate network is not an option. Is it possible to implement a procedure similar to the “I...... <less SNAP-PAC-R2 Firmware '...FTP Session Failed' Forum - Published: Am trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172...moreAm trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172.25.0.9 - Attempt to open FTP session failed”., note: the IP address is correct. I have tried using PAC Manager 9.0, 9.6 & 10.2; all produce the same error. Following the directions in the PAC Manager User Guide. I thought I had trouble with this years ago, but can’t locate any Opto help infor...... <less Firmware update Forum - Published: Hi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect...moreHi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect to it. I currently have this firmware R9.5h And also, if I update the firmware for the SNAP-PAC-R1, i have two other I/O hooked up to it, SNAP-PAC-EB1. do I also have to update the firmware for those too?... <less What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
SNAP-PAC-R1 firmware upgradation failed Forum - Published: Hi all. I am using SNAP-PAC-R1 controller for my application. I tried to update the firmware of the module to R9.5h via Ethernet. During firmware downloading process suddenly an error called insufficient...moreHi all. I am using SNAP-PAC-R1 controller for my application. I tried to update the firmware of the module to R9.5h via Ethernet. During firmware downloading process suddenly an error called insufficient flash memory occurred. From then module is not responding. I tried to reset and restore. But no use. Please help me to resolve the issue and make my R1 to running state. Present situation is very worst. STAT LED blinks twice after power up and then it will goes OFF. No response from controller.... <less SNAP-PAC-EB1 Install Firmware via Ethernet Passthrough Connection Forum - Published: We configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With...moreWe configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With this configuration we alienate ourselves from inspecting the EB1 and installing firmware to the EB1 unless we are physically at the device. Not practicable for all of our remote locations. Building out a separate network is not an option. Is it possible to implement a procedure similar to the “I...... <less SNAP-PAC-R2 Firmware '...FTP Session Failed' Forum - Published: Am trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172...moreAm trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172.25.0.9 - Attempt to open FTP session failed”., note: the IP address is correct. I have tried using PAC Manager 9.0, 9.6 & 10.2; all produce the same error. Following the directions in the PAC Manager User Guide. I thought I had trouble with this years ago, but can’t locate any Opto help infor...... <less Firmware update Forum - Published: Hi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect...moreHi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect to it. I currently have this firmware R9.5h And also, if I update the firmware for the SNAP-PAC-R1, i have two other I/O hooked up to it, SNAP-PAC-EB1. do I also have to update the firmware for those too?... <less What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
SNAP-PAC-EB1 Install Firmware via Ethernet Passthrough Connection Forum - Published: We configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With...moreWe configure our EB1’s with a non-routable ip address common to the controller’s ENET 2 port. By doing so it keeps all the i/o traffic local and isolated…straight out of the SNAP PAC User’s Guide. With this configuration we alienate ourselves from inspecting the EB1 and installing firmware to the EB1 unless we are physically at the device. Not practicable for all of our remote locations. Building out a separate network is not an option. Is it possible to implement a procedure similar to the “I...... <less SNAP-PAC-R2 Firmware '...FTP Session Failed' Forum - Published: Am trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172...moreAm trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172.25.0.9 - Attempt to open FTP session failed”., note: the IP address is correct. I have tried using PAC Manager 9.0, 9.6 & 10.2; all produce the same error. Following the directions in the PAC Manager User Guide. I thought I had trouble with this years ago, but can’t locate any Opto help infor...... <less Firmware update Forum - Published: Hi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect...moreHi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect to it. I currently have this firmware R9.5h And also, if I update the firmware for the SNAP-PAC-R1, i have two other I/O hooked up to it, SNAP-PAC-EB1. do I also have to update the firmware for those too?... <less What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
SNAP-PAC-R2 Firmware '...FTP Session Failed' Forum - Published: Am trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172...moreAm trying to install firmware R9.5h onto an R2 brain with R10.3 b firmware. Trying to troubleshoot some older alarm logic in Strategy, thinking this may help. But, regardless, I continue to get the “172.25.0.9 - Attempt to open FTP session failed”., note: the IP address is correct. I have tried using PAC Manager 9.0, 9.6 & 10.2; all produce the same error. Following the directions in the PAC Manager User Guide. I thought I had trouble with this years ago, but can’t locate any Opto help infor...... <less Firmware update Forum - Published: Hi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect...moreHi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect to it. I currently have this firmware R9.5h And also, if I update the firmware for the SNAP-PAC-R1, i have two other I/O hooked up to it, SNAP-PAC-EB1. do I also have to update the firmware for those too?... <less What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Firmware update Forum - Published: Hi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect...moreHi all, I’m fairly new to this. I’m looking to see if updating the firmware to my controller it would improve the communication. what i mean by that, controller times out a lot whenever i try to connect to it. I currently have this firmware R9.5h And also, if I update the firmware for the SNAP-PAC-R1, i have two other I/O hooked up to it, SNAP-PAC-EB1. do I also have to update the firmware for those too?... <less What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
What you need in order to use RIO with a SNAP PAC Controller Forum - Published: Hey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version...moreHey RIO fans. If you are looking to use RIO with your SNAP PAC controller, you will need two things. PAC Project 10.3 or better. Get your version from here; Opto22 - Product Selector Firmware version 10.3 or better. Get your version from here; Opto22 - Firmware for all SNAP PAC products Configure the RIO just as you would any other remote IO unit like an EB for example and you can set up the IO and go from there. Keep in mind that if you first configure the IO via groov Manage, when you down...... <less The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
The problem of firmware upgrading Forum - Published: Excuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old...moreExcuse me, I have a controller, SNAP-UP1-ADS, firmware is R7.2i, it takes a long time. When it worked with PAC Control 9.6, PAC Control recommended that I upgrade firmware to R8.5c. Can I ask this old guy to be able to upgrade to R8.5c? image.jpg1440×1080 966 KB image.jpg1080×1440 473 KB Thank you... <less Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Controller Firmware version as a Tag/Variable? Forum - Published: Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains....Has anyone ever tried pulling firmware versions of the controllers into an HMI via a tag? We’re running Older Snap-LCM4 and Snap-Pac controllers, and I’d like to monitor the firmware currently installed on the controller and brains.... <less Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Updating the Loader on a SNAP R2-W Device Forum - Published: hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model....hi, i have a snap pac r2-w with Loader Version R6.0b, i want to upgrade to install a 16gb SD. You can tell me the correct firmware download link for it, since the one on the page does not apply to my model.... <less Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Update Snap EB2 Forum - Published: hi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special...morehi, I have an EB2 snap with firmware version 8.5, I want to update it to the latest version available, to do it it generates an error “not enough space for firmware file”; is there any special procedure to update? Should updates be done in sequence? Thanks a lot.... <less Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Access to SNAP-R1 Firmware 10.4 Forum - Published: We have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware...moreWe have a fresh out of the package Gen1 SNAP-PAC-R1. When we attempt to update the firmware to the latest version (10.5g) available from the website, the updater fails with an “incompatible hardware” message. Fortunately, I still had a copy of 10.4d saved, because without an update, our (PacControl 10.5) strategy wouldn’t load to the out-of-the-box firmware version. Is this an issue where 10.4 needs to be kept available on the website for folks like us that might still have legacy SNAP PACs in t...... <less How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
How I upgraded my SNAP PAC controllers to version 9.5 and the RESTful interface Forum - Published: Recently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to...moreRecently, I upgraded my SNAP PAC controllers to firmware version R9.5a and enabled the RESTful server on my PACs. I’ve outlined the steps that I took in a blog post, and thought they’d be helpful to the OptoForums community interested in kicking the RESTful tires of the new firmware. The instructions include how I used the new OptoTagPreserve to preserve my persistent variables before the download, and then again to reapply my persistents after the firmware upgrade. Here’s the link to the blog p...... <less Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Firmware upgrade failed: "Not enough space for response file" Forum - Published: I tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but...moreI tried to update my firmware from R9.4b to R9.5d on my SNAP-PAC-R1 but received the following message: “Not enough space for response file.” Then PAC Manager attempted to install a bridge firmware but failed and prompted me to see KB82101. The knowledge based article described an issue for PAC Manager version R9.2c however I am running PAC Manager version R9.4c. In the PAC Managers users guide(document 1704) it mentions on p207 “If download fails… there might not be enough file space for the ne...... <less Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov Configure Devices & Tags not working Forum - Published: We upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and...moreWe upgraded groov to the R2.1a with build date 3/6/2014 12:49 pm. Since then we are unable to add opto 22 controller (tag import) into groov. When I click on import the progress indicator come on and stay there for hours. I’ve tried most popular browsers (IE, Chrome, Firefox, and Safari) our settings are snap pac R1 Controller firmware R9.3c groov R2.1a build date 3/6/2014 12:49 pm. Please help!... <less How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Forum - Published: How to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be...moreHow to read AI/DI from SNAP-PAC-S2/EB brains to a local server without changing the running strategy? + HMI brand compatibility Hi everyone, I have a SNAP-PAC-S2 running a plant process (cannot be stopped right now). We recently added a site-wide SCADA, so the process is visible. Now I need to log real sensor data to a local server. Constraints & context: Controller: SNAP-PAC-S2, firmware R8.5d (no REST API). I/O is on Ethernet brains in the same LAN: EB1_1 = SNAP-PAC-EB1 @ 192.168.100.19 (Enabl...... <less PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
PAC CONTROL BASIC 10.3b FIRMWARE issue W10 Forum - Published: hi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the...morehi we had a working old SNAP PAC R2 and opto logic and our visual basic MMP software working - and after 10 years client wanted to upgrade components - we purchased new SNAP PAC R2 controller- and the firmware is newer than what our development of software developed using visualbasic MMP. so we found out the newer controllers cant go past 10.3b - so we installed 10.3b on newer controller. Opto 22 Product Support Reference # 119119 our visualbasic MMP software seems to work and intermittently and...... <less PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
PID loop on GROOV Forum - Published: Hi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in...moreHi all, Could you please provide help/documentation regarding PID loop implementation on a GROOV EPIC, with AI and AO modules using PAC Control? Any examples that could help? Is this control in relation with the processor firmware version? Is it different from PID on SNAP? Thx.... <less Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Upgraded Firmware/Loader/PAC Project and now PAC Display updates significantly slower Forum - Published: I’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I...moreI’m using a SNAP-PAC-R1 controller. The project I created ran on Firmware 9.4b and loader 6.1b and using PAC Project Software Suite 9.4. PAC Display runtime would refresh the color of a button I created based on a numeric value received. It lags about 3 seconds before the color updates, even though the group refresh value is 50ms. But that’s a different problem to figure out. Once I loaded the latest firmware, R10.4c, and loader R6.2c and used PAC Project 10.4 and ran the project, my PAC Display...... <less Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Port Static IP change to DHCP Forum - Published: Hey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that...moreHey Guys, I have recently upgraded my Groov EPIC firmware to the latest. Before upgradation I have configured ETH0 port IP address as a static IP (192.168.56.108). But after upgradation I found that ETH0 port IP address(192.168.56.29) and network option as a DHCP. Why EPIC does not save its last IP address like SNAP-PAC Controller during upgradation? Is there any option for that? Thanks & Regards, Aanand... <less Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Opto22 DataLink Forum - Published: Hi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example...moreHi, I have been trying to explore and learn about Optodatalink. I am using PAC Project 10.5 the latest version and i have the latest firmware installed on SNAP-PAC R1 Brain. I am using the example strategy in the learning center package that the manual refers to, and every time i try to select the control engine for the tags, the software crashes. is there anything i should do or try to fix this issue? Thank you and i really appreciate the help... <less S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
S1 First Generation to PROJECTPRO R.10 Forum - Published: I have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple...moreI have two first generation SNAP-PAC-S1 controllers that I installed in a system about 2007. The S1’s are communicating with some old B3000 brains using RS-485. Well, they want an upgrade as simple as possible, so I am installing SNAP-PAC-RCK16’s with EB2 brains (which allows me to use all the same I/O and go all Ethernet) Has anyone upgraded a first generation S1 to use the PROJECTPRO R.10? I will be upgrading the firmware of course, but that is quite a jump. I am just wondering if anyone h...... <less OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
OptoTagPreserve Assistance Forum - Published: Hi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload...moreHi All, So I thought I had all my ducks in a row to update my SNAP-PAC-R1 firmware to R10.4d without losing my calibrated points. I backed up my control strategy, then used OptoTagPreserve to upload my tags. I updated the firmware using Manager and then I’ll admit, at first I forgot to re-load my strategy. So I ran the restore function of OptoTagPreserve and it obviously failed because of the missing tags. I loaded my control strategy by selecting debug in Control (I didn’t run it). Then I ...... <less Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Problem with 1678 Modbus/TCP Protocol Guide Forum - Published: I have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG...moreI have found what appears to me to be an error on Page 29 of the Modbus/TCP Protocol Guide in the Analog Module Address Table. This pertains to the values used for both the CONFIG POINT and CONFIG FEATURE. For reference: I am using a SNAP-PAC-EB1 brain with firmware R8.5e on a SNAP-PAC-RCK12 and have been experimenting by moving a SNAP-AIMA 2 channel module around to different positions along with some input and output modules. According to the table each module position has 128 registers reserv...... <less Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Controller blocked Forum - Published: Controller: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control...moreController: SNAP-PAC-S1 Firmware: R9.4a Loader: R3.1c Software: PAC Project R9.4007 PAC Control Professional: R9.4d Build Date: Mar 31 2015 No communication with controller (no ip ping, no display runtime, no PAC Manager, no PAC Terminal), controller is blocked After it doing manually turn off and manually turn on the controller has these errors: -539 Info I/O ...... <less Page 1 of 8Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items