Can I email using an address that isn't gmail or yahoo? Forum - Published: I’ve managed to follow Terry’s videos and successfully use a Rio & node-RED to send a file to my gmail address. Yay! But here is the but… I’ve been asked to get it sent to an (outlook) email address...more I’ve managed to follow Terry’s videos and successfully use a Rio & node-RED to send a file to my gmail address. Yay! But here is the but… I’ve been asked to get it sent to an (outlook) email address that ends in @nrcan-rncan.gc.ca; and it’s not working. I thought I had read somewhere that the rio / EPIC will only send to gmail & yahoo accounts, but now I can’t find it anywhere so not sure if that’s even true. The Rio user guide & the knowledge base articles / technical notes I can find seem to ...... <less Use of pointers in CODESYS Forum - Published: i use pointer in pack control for batch recipes, I don’t know how to do so in codesys. In PacControl I place digital outputs in a pointer table and with a index variable I move one element of pointer...morei use pointer in pack control for batch recipes, I don’t know how to do so in codesys. In PacControl I place digital outputs in a pointer table and with a index variable I move one element of pointer table to a pointer variable. Pac example //addressing pointer table to digital output pt_Products_Valves[1]=&do_0101; pt_Products_Valves[2]=&do_0102; pt_Products_Valves[3]=&do_0103; //addressing pointer variable wtih pointer table index p_Batch_Valve=pt_Products_Valves[n_Operator_BatchProduct_Sele...... <less RIO EMU and using a non Opto22 CT Forum - Published: Planning on using a CT that doesn’t fall into one of 3 ranges for the RIO EMU (Opto 22 groov energy monitoring products can support CTs with a 5 A, 1.0 VAC, or 0.333 VAC secondary.). RCT24-5000. Looks to...morePlanning on using a CT that doesn’t fall into one of 3 ranges for the RIO EMU (Opto 22 groov energy monitoring products can support CTs with a 5 A, 1.0 VAC, or 0.333 VAC secondary.). RCT24-5000. Looks to be 24mV per 1000A. Primary is 25A to 6000A. Which should output on the secondary 0mV to 144mv. Looking at the settings I would need to do some adjustments to how this is scaled. Hopefully not a dumb question. First time using an EMU. Is it recommended to use a CT that matches one of the 3 range ...... <less Groov Server Access issue Forum - Published: Hello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it...moreHello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it. Earlier it was working good. Can some one help me to resolve issue. Please see the attached screen snip. image1343×534 30.9 KB... <less Groov EPIC I/O Not Syncing to PAC Control I/O Forum - Published: Hello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or...moreHello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or sync that I can perform to get the tags to update? Thanks, Dan Groov EPIC IO780×446 16.5 KB pac control io987×281 56 KB... <less Serial Communication S1 Controller To PR1 GRV-CSERI-4 Forum - Published: Is this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale...moreIs this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale using the GRV-CSERI-4 Module? @WT_601A_TRAILER_1_SERIAL:baud=9600,parity=n,data=8,stop=1 image446×792 23.6 KB image817×149 3.96 KB image817×824 49.8 KB... <less Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Use of pointers in CODESYS Forum - Published: i use pointer in pack control for batch recipes, I don’t know how to do so in codesys. In PacControl I place digital outputs in a pointer table and with a index variable I move one element of pointer...morei use pointer in pack control for batch recipes, I don’t know how to do so in codesys. In PacControl I place digital outputs in a pointer table and with a index variable I move one element of pointer table to a pointer variable. Pac example //addressing pointer table to digital output pt_Products_Valves[1]=&do_0101; pt_Products_Valves[2]=&do_0102; pt_Products_Valves[3]=&do_0103; //addressing pointer variable wtih pointer table index p_Batch_Valve=pt_Products_Valves[n_Operator_BatchProduct_Sele...... <less RIO EMU and using a non Opto22 CT Forum - Published: Planning on using a CT that doesn’t fall into one of 3 ranges for the RIO EMU (Opto 22 groov energy monitoring products can support CTs with a 5 A, 1.0 VAC, or 0.333 VAC secondary.). RCT24-5000. Looks to...morePlanning on using a CT that doesn’t fall into one of 3 ranges for the RIO EMU (Opto 22 groov energy monitoring products can support CTs with a 5 A, 1.0 VAC, or 0.333 VAC secondary.). RCT24-5000. Looks to be 24mV per 1000A. Primary is 25A to 6000A. Which should output on the secondary 0mV to 144mv. Looking at the settings I would need to do some adjustments to how this is scaled. Hopefully not a dumb question. First time using an EMU. Is it recommended to use a CT that matches one of the 3 range ...... <less Groov Server Access issue Forum - Published: Hello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it...moreHello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it. Earlier it was working good. Can some one help me to resolve issue. Please see the attached screen snip. image1343×534 30.9 KB... <less Groov EPIC I/O Not Syncing to PAC Control I/O Forum - Published: Hello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or...moreHello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or sync that I can perform to get the tags to update? Thanks, Dan Groov EPIC IO780×446 16.5 KB pac control io987×281 56 KB... <less Serial Communication S1 Controller To PR1 GRV-CSERI-4 Forum - Published: Is this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale...moreIs this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale using the GRV-CSERI-4 Module? @WT_601A_TRAILER_1_SERIAL:baud=9600,parity=n,data=8,stop=1 image446×792 23.6 KB image817×149 3.96 KB image817×824 49.8 KB... <less Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
RIO EMU and using a non Opto22 CT Forum - Published: Planning on using a CT that doesn’t fall into one of 3 ranges for the RIO EMU (Opto 22 groov energy monitoring products can support CTs with a 5 A, 1.0 VAC, or 0.333 VAC secondary.). RCT24-5000. Looks to...morePlanning on using a CT that doesn’t fall into one of 3 ranges for the RIO EMU (Opto 22 groov energy monitoring products can support CTs with a 5 A, 1.0 VAC, or 0.333 VAC secondary.). RCT24-5000. Looks to be 24mV per 1000A. Primary is 25A to 6000A. Which should output on the secondary 0mV to 144mv. Looking at the settings I would need to do some adjustments to how this is scaled. Hopefully not a dumb question. First time using an EMU. Is it recommended to use a CT that matches one of the 3 range ...... <less Groov Server Access issue Forum - Published: Hello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it...moreHello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it. Earlier it was working good. Can some one help me to resolve issue. Please see the attached screen snip. image1343×534 30.9 KB... <less Groov EPIC I/O Not Syncing to PAC Control I/O Forum - Published: Hello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or...moreHello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or sync that I can perform to get the tags to update? Thanks, Dan Groov EPIC IO780×446 16.5 KB pac control io987×281 56 KB... <less Serial Communication S1 Controller To PR1 GRV-CSERI-4 Forum - Published: Is this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale...moreIs this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale using the GRV-CSERI-4 Module? @WT_601A_TRAILER_1_SERIAL:baud=9600,parity=n,data=8,stop=1 image446×792 23.6 KB image817×149 3.96 KB image817×824 49.8 KB... <less Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov Server Access issue Forum - Published: Hello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it...moreHello, I have installed Groov Server on my computer. I am trying to connect it through web server. But I am facing below issue. I have tried by changing port number. Still not able to connect with it. Earlier it was working good. Can some one help me to resolve issue. Please see the attached screen snip. image1343×534 30.9 KB... <less Groov EPIC I/O Not Syncing to PAC Control I/O Forum - Published: Hello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or...moreHello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or sync that I can perform to get the tags to update? Thanks, Dan Groov EPIC IO780×446 16.5 KB pac control io987×281 56 KB... <less Serial Communication S1 Controller To PR1 GRV-CSERI-4 Forum - Published: Is this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale...moreIs this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale using the GRV-CSERI-4 Module? @WT_601A_TRAILER_1_SERIAL:baud=9600,parity=n,data=8,stop=1 image446×792 23.6 KB image817×149 3.96 KB image817×824 49.8 KB... <less Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov EPIC I/O Not Syncing to PAC Control I/O Forum - Published: Hello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or...moreHello, My Groov EPIC does not seem to be updating the tag list on the EPIC processer to match the PAC Control Strategy. I’ve attached a couple images to show what I’m talking about. Is there an update or sync that I can perform to get the tags to update? Thanks, Dan Groov EPIC IO780×446 16.5 KB pac control io987×281 56 KB... <less Serial Communication S1 Controller To PR1 GRV-CSERI-4 Forum - Published: Is this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale...moreIs this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale using the GRV-CSERI-4 Module? @WT_601A_TRAILER_1_SERIAL:baud=9600,parity=n,data=8,stop=1 image446×792 23.6 KB image817×149 3.96 KB image817×824 49.8 KB... <less Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Serial Communication S1 Controller To PR1 GRV-CSERI-4 Forum - Published: Is this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale...moreIs this the proper syntax for a communication handle where a S1 controller is the main controller that is talking to a groovEpic PR1 used as just a brain to bring in serial communication from a scale using the GRV-CSERI-4 Module? @WT_601A_TRAILER_1_SERIAL:baud=9600,parity=n,data=8,stop=1 image446×792 23.6 KB image817×149 3.96 KB image817×824 49.8 KB... <less Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Access Codesys Tag Values Via REST API? Forum - Published: We are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime...moreWe are evaluating using the EPIC for a large number of asphalt plant automation installs. Our primary application lives in the browser. If our plant automation logic is written using the Codesys runtime are those tags/variables accessible through the documented PAC Control REST API? We are primarily web devs, so working at the HTTP / REST API layer is our comfort zone.... <less Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov View - EPIC PR1 connection lost upon Windows PC restart Forum - Published: Hello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is...moreHello, I currently have a PR1 connected directly to a Windows PC via an ethernet connection. My groov View HMI is connected to my PAC Control strategy as an Opto 22 Controller, and the strategy is started from my groov Manage interface. If my Windows PC requires a restart (thanks Windows Update!) my strategy continues operating as normal (I can monitor I/O points and do changes via groov Manage) but my groov View interface freezes up and does not refresh process variable values or recognize user...... <less Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Communication between R1 and Schneider PLC Forum - Published: Hello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function...moreHello everyone, one of my customers has an opto22 R1 control system and two Schneider PLC control systems. He wants to achieve communication between R1 and Schneider PLC. I want to achieve this function through Modbus/TCP. I can complete the Modbus/TCP communication development work on R1. I am not very clear about Schneider PLC. Does Schneider PLC also need to add corresponding programs? Schneider PLC supports network communication.I´m using PAC Control Professional R9.6. Thank you so much!... <less Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov RIO to EPIC Forum - Published: What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You...What is the best way to see I/O points on a Groov RIO that is on the same network as and EPIC. I would like to use the EPIC as my main clearing house for taking action on I/O points. Thank You... <less GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
GRV-EPIC-IV-24 Resolution Forum - Published: I’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The...moreI’m looking at a project that would test multiple sensors using a GRV-EPIC-IV-24, EPIC 24 channel voltage input module. Each sensor can have a different output, for example 0-5 VDC or 0-10 VDC. The required accuracy is 0.1% so for the 10 VDC sensors, that’s 10 mV and the 5 VDC sensors, 5 mV. The module spec says it supports 0.1% accuracy for the configured range, so if the input channel is configured for 10 VDC, the accuracy is 10 mV, etc. I don’t know which sensor will be connected to each inp...... <less Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Codesys Permission Log Errors Forum - Published: I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB...I have a project that seems to be run okay but I notice in the log that there is permission errors that looked linked to the system scheduler. Is there anything I can do to resolve these errors. A screen shot can be found below: image871×442 12.7 KB... <less PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
PAC-R1 GEN2 Controller Forum - Published: Since the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to...moreSince the new redesigned R1 has a new chip set, did that have any effect on the issue with using stop/start chart and all the other chart functions that previously required up to 100ms wait time to assure that the action had taken place? Also, why not replace the Ether ports with 10/100/1000? We still love the R1, incredible controller, even by today’s standards. Also much simpler implementation versus Epic.... <less Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Communication Problem with TCP/IP Groov Epic Forum - Published: When I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn...moreWhen I use these commands the port never opens, I get a -440 error. / listen for connections // we will be here till we get a connection unless something bad happens rtn = ListenForIncomingCommunication(In_Control_Panel); //NumberToString(rtn, aStr); //aStr = “Listen rtn:”+aStr; //print(diagHandle, aStr); If (IsCommunicationOpen(In_Control_Panel) == False) then AcceptIncomingCommunication(In_Control_Panel); Else GetNumCharsWaiting(In_Control_Panel); EndIf DelayMsec(500); Start_Communication = O...... <less Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Reset with custom image Forum - Published: My apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It...moreMy apologies if this is the wrong category, I have a whole bunch of groov RIO. A colleague of mine has created a means of reprovisioning the Groov Rio after the reset button has been pressed. It however requires network setup, and will not load the custom binaries, shell license etc. I believe he used selenium macros. I digress. It occurred to me that the means of resetting is to load an image (boot image) from a location that the user does not normally access, and that pressing the reset butto...... <less CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
CODESYS V3.5.and Opto22-3.1.1.0 CODESYS Library Forum - Published: I have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to...moreI have the following setup for CODESYS: * CODESYS V3.5 SP20 Parch 2 + (32-bit) IDE * Opto22-3.1.1.0-codesys-b2 package * OSCATBasic package * groov EPIC System Firmware Version 3.6.0-b.32 When I go to create a new project, I get the following errors: Could not open library ‘Component Manager, 3.5.13.0 (System)’. (Reason: The library ‘Component Manager, 3.5.13.0 (System)’ has not been installed to the system.) 3.5.17.0 Could not open library ‘SysTimeCore, 3.5.5.0 (System)’. (Reason: The libr...... <less Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Better to have all I/O controls all in one chart? Forum - Published: I am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to...moreI am unsure how to even ask this, let alone how to look for it and I would like to point out that because of this, I didn’t look to see if there were any threads about this already. And I would like to apologize beforehand if there is. I was a part of the class that was at the beginning of June of this year and that was my first time programming anything PLC like, so I am very new to this. But something came to mind today that I wish I would have come to me while I was in the class so I could as...... <less -539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
-539 I/O error; performing retry Forum - Published: SNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last...moreSNAP PAC EB2 brain is returning -539 in the controller message queue. image1163×623 364 KB The brain is only referenced in two block2 and runs ~100 msecs between blocks and ~10 msecs after the last block before the first is read again. image1274×733 26.8 KB image1274×733 27.9 KB Power is good. SNAP-PAC-EB2 brain has been replaced. Ethernet cable has been replaced. Any ideas? Does this error relate to communication with the SNAP-PAC-EB2 brain or is there an issue with a module on the SNAP-PAC-EB2...... <less GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
GRV-IDCSW-12, common supply Forum - Published: Can the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the...moreCan the supply for several inputs be connected together to monitor several contact closures? For example, pins 2, 4, 6 connected together and to the “common” terminals of three SPST switches and the NO terminals connected to pins 1, 2, 5 respectively. This would permit the use of four conductors instead of six.... <less PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
PAC Control on EPIC Forum - Published: I am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years...moreI am looking for some PAC Control coding support as I cannot think of a method of achieving what my customer is requesting. Background I installed an EPIC PR1, serial module and DI module some years ago to provide a client with a tank farm level monitoring system. It uses PAC Control and Opto Modbus Integration Kit to get Modbus RTU data via the serial card from Tank Volume and Temperature gauges. This is displayed on the clients PC using PAC Display with Supertrends. There are 30 tanks on site ...... <less Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Grv-cseri-4 (rs232) Forum - Published: Good day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all...moreGood day, I am needing some assistance into a small challenge I am currently encountering. I have connected a scale indicator (transmitting RS232) to the CSERI-4 (configured for RS232). Configured all the connection strings and comm-handles and connected to the indicator. When connected to the CSERI I receive a string as per string 1 image below, whole lot of random. (Baud Rates and all parameters are correct, wiring is correct and routing works) There are to versions of the scale indicators con...... <less Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Codesy device user pasword Forum - Published: Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks...Hi all I forget the user name in codesys device user Logon Gratefull if anyone can help Thanks... <less Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Ignition Gateway OPC error, caused by Groov Epic running codesys Forum - Published: David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the...more David_HargisToday is the anniversary of the day you joined our community! 1m We have an Ignition Gateway that lost its OPC Connections to 3 separate Opto-22 Groov Epic R2 Controllers, all running the CodeSys platform. The following was the log error message on the gateway. The OPC interfaces are used to bring the CodeSys program tags into Ignition. As far as we know, there was nothing weird about the network setup. There are about 100 devices on the static IP network. Most of the “Traffic” is e...... <less I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
I Need Advice on Choosing the Right Opto 22 Controller for a Small-Scale Automation Project Forum - Published: Hey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to...moreHey guys… I am currently working on a small-scale automation project for a local food processing company. The aim is to automate some of their manual processes, such as packaging and labeling, to improve efficiency and reduce human error. After some research, I have narrowed down my choice to either the groov EPIC or the SNAP PAC system but I am not sure which would be the best fit for this project. Here is the some highlights of project: We need to control around 20 digital I/O points and 5 a...... <less Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Can R1 communicate with IEC61850 devices? Forum - Published: Can R1 communicate with IEC61850 devices?...Can R1 communicate with IEC61850 devices?... <less Page 1 of 46Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items